qn1569811893

qn1569811893

0个粉丝

2

问答

0

专栏

0

资料

qn1569811893  发布于  2019-09-30 11:50:59
采纳率 0%
2个问答
4076

海思3516av200按照SDK烧录进去后内核无法启动

 
按照海思3516av200的SDK,把u-boot-hi3516av200.bin  uImage_hi3516av200 rootfs_hi3516av200_64k.jffs2烧录进去后内核启动不了,有没有大牛知道这是怎么回事额!用的是16m的spiFLASH


System startup


U-Boot 2010.06 (Jul 05 2018 - 11:14:28)

Check Flash Memory Controller v100 ... Found
SPI Nor(cs 0) ID: 0xc2 0x20 0x18
Block:64KB Chip:16MB Name:"MX25L128XX"
SPI Nor total size: 16MB
MMC:   
EMMC/MMC/SD controller initialization.
Card did not respond to voltage select!
No EMMC/MMC/SD device found !
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  0
16384 KiB hi_fmc at 0:0 is now current device

## Booting kernel from Legacy Image at 82000000 ...
   Image Name:   Linux-3.18.20
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3086342 Bytes = 2.9 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Loading Kernel Image ... OK
OK
Starting kernel ...

Booting Linux on physical CPU 0x0
Initializing cgroup subsys cpu
Linux version 3.18.20 (root@machine) (gcc version 4.9.4 20150629 (prerelease) (Hisilicon_v500_20180120) ) #1 SMP Sun Sep 29 15:38:22 CST 2019
CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Hisilicon HI3516AV200 DEMO Board
cmz zone is not set!
cma: Reserved 16 MiB at 0x83000000
Memory policy: Data cache writealloc
PERCPU: Embedded 9 pages/cpu @c2f4e000 s7424 r8192 d21248 u36864
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: mem=64M console=ttyAMA0,115200 root=/dev/mtdblock2 rootfstype=jffs2 rw mtdparts=hi_sfc:1M(boot),3M(kernel),12M(rootfs)
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 42164K/65536K available (4291K kernel code, 201K rwdata, 1132K rodata, 220K init, 349K bss, 23372K reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xffe00000   (2048 kB)
    vmalloc : 0xc4800000 - 0xff000000   ( 936 MB)
    lowmem  : 0xc0000000 - 0xc4000000   (  64 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc0554048   (5425 kB)
      .init : 0xc0555000 - 0xc058c000   ( 220 kB)
      .data : 0xc058c000 - 0xc05be600   ( 202 kB)
       .bss : 0xc05be600 - 0xc0615a7c   ( 350 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
        RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
Architected cp15 timer(s) running at 24.00MHz (phys).
sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
Switching to timer-based delay loop, resolution 41ns
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x804184a0 - 0x804184f8
ARM CCI driver probed
CPU1: Booted secondary processor
CPU1: thread -1, cpu 0, socket 1, mpidr 80000100
Brought up 2 CPUs
SMP: Total of 2 processors activated (96.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
regulator-dummy: no parameters
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor ladder
cpuidle: using governor menu
Serial: AMBA PL011 UART driver
12100000.uart: ttyAMA0 at MMIO 0x12100000 (irq = 36, base_baud = 0) is a PL011 rev2
console [ttyAMA0] enabled
SCSI subsystem initialized
ssp-pl022 12120000.spi: ARM PL022 driver, device ID: 0x00800022
ssp-pl022 12120000.spi: mapped registers from 0x12120000 to fea20000
ssp-pl022 12121000.spi: ARM PL022 driver, device ID: 0x00800022
ssp-pl022 12121000.spi: mapped registers from 0x12121000 to fea21000
ssp-pl022 12121000.spi: cs1 >= max 1
spi_master spi1: spi_device register error /soc/amba/spi@12121000/spidev@1
ssp-pl022 12122000.spi: ARM PL022 driver, device ID: 0x00800022
ssp-pl022 12122000.spi: mapped registers from 0x12122000 to fea22000
ssp-pl022 12123000.spi: ARM PL022 driver, device ID: 0x00800022
ssp-pl022 12123000.spi: mapped registers from 0x12123000 to fea23000
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switched to clocksource arch_sys_counter
INFO: rcu_sched self-detected stall on CPU { 0}  (t=8948 jiffies g=-291 c=-292 q=22)
Task dump for CPU 0:
swapper/0       R running      0     0      0 0x00000000
[] (unwind_backtrace) from [] (show_stack+0x10/0x14)
[] (show_stack) from [] (rcu_dump_cpu_stacks+0x94/0xd4)
[] (rcu_dump_cpu_stacks) from [] (rcu_check_callbacks+0x3c4/0x664)
[] (rcu_check_callbacks) from [] (update_process_times+0x40/0x60)
[] (update_process_times) from [] (tick_nohz_handler+0xac/0x120)
[] (tick_nohz_handler) from [] (arch_timer_handler_phys+0x28/0x30)
[] (arch_timer_handler_phys) from [] (handle_percpu_devid_irq+0x6c/0x84)
[] (handle_percpu_devid_irq) from [] (generic_handle_irq+0x2c/0x3c)
[] (generic_handle_irq) from [] (__handle_domain_irq+0x5c/0xa4)
[] (__handle_domain_irq) from [] (gic_handle_irq+0x24/0x78)
[] (gic_handle_irq) from [] (__irq_svc+0x40/0x54)
Exception stack(0xc058df48 to 0xc058df90)
df40:                   ffffffed 00000000 ffffffed c00199a0 c058c018 c0594460
df60: c05944c4 00000000 00000000 00000000 c058c000 c041a9b0 c059521c c058df90
df80: c000f0e4 c000f0e8 60000113 ffffffff
[] (__irq_svc) from [] (arch_cpu_idle+0x38/0x3c)
[] (arch_cpu_idle) from [] (cpu_startup_entry+0x228/0x29c)
[] (cpu_startup_entry) from [] (start_kernel+0x398/0x3a4)
[] (start_kernel) from [<80008074>] (0x80008074)
Task dump for CPU 1:
swapper/0       R running      0     1      0 0x00000000
[] (__schedule) from [] (0xc0594700)
INFO: rcu_sched detected stalls on CPUs/tasks: { 1} (detected by 0, t=35807
我来回答
回答0个
时间排序
认可量排序
易百纳技术社区暂无数据
或将文件直接拖到这里
悬赏:
E币
网盘
* 网盘链接:
* 提取码:
悬赏:
E币

Markdown 语法

  • 加粗**内容**
  • 斜体*内容*
  • 删除线~~内容~~
  • 引用> 引用内容
  • 代码`代码`
  • 代码块```编程语言↵代码```
  • 链接[链接标题](url)
  • 无序列表- 内容
  • 有序列表1. 内容
  • 缩进内容
  • 图片![alt](url)
+ 添加网盘链接/附件

Markdown 语法

  • 加粗**内容**
  • 斜体*内容*
  • 删除线~~内容~~
  • 引用> 引用内容
  • 代码`代码`
  • 代码块```编程语言↵代码```
  • 链接[链接标题](url)
  • 无序列表- 内容
  • 有序列表1. 内容
  • 缩进内容
  • 图片![alt](url)
相关问答
无更多相似问答 去提问
举报反馈

举报类型

  • 内容涉黄/赌/毒
  • 内容侵权/抄袭
  • 政治相关
  • 涉嫌广告
  • 侮辱谩骂
  • 其他

详细说明

易百纳技术社区