3873
- 收藏
- 点赞
- 分享
- 举报
关于080版本初始化问题
大家好,我使用hi3516av100spc080芯片,原来使用040的SDK,运行程序,相机指向kernel不匹配,后来使用080的SDK结果发现,uboot网络不通,kernel运行结果有问题,使用的均是官方提供的,很奇怪
U-Boot 2010.06 (Jun 04 2015 - 14:17:45)
NAND: Check nand flash controller v610. found
Special NAND id table Version 1.36
Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
No NAND device found!!!
0 MiB
Check spi flash controller v350... Found
Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18
Spi(cs1): Block:64KB Chip:16MB Name:"MX25L128XX"
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
16384 KiB hi_sfc at 0:0 is now current device
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-4.9.37
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3100884 Bytes = 3 MiB
Load Address: 80008000
Entry Point: 80008000
Loading Kernel Image ... OK
OK
Starting kernel ...
Booting Linux on physical CPU 0x0
Linux version 4.9.37 (pub@BVT-SDK-SERVER1) (gcc version 6.2.1 20161016 (Hisilicon_v510_20171125) ) #1 Wed Jan 3 14:02:51 HKT 2018
CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
CPU: div instructions available: patching division code
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
OF: fdt:Machine model: Hisilicon HI3516A DEMO Board
Memory policy: Data cache writeback
CPU: All CPU(s) started in SVC mode.
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: mem=64M console=ttyAMA0,115200 root=/dev/mtdblock2 rootfstype=jffs2 mtdparts=hi_sfc:1M(boot),3M(kernel),12M(rootfs)
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 58488K/65536K available (4673K kernel code, 184K rwdata, 1032K rodata, 188K init, 252K bss, 7048K reserved, 0K cma-reserved)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xc4800000 - 0xff800000 ( 944 MB)
lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc0498980 (4675 kB)
.init : 0xc059d000 - 0xc05cc000 ( 188 kB)
.data : 0xc05cc000 - 0xc05fa160 ( 185 kB)
.bss : 0xc05fc000 - 0xc063b048 ( 253 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:16 nr_irqs:16 16
clocksource: arm,sp804: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns
sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns
Console: colour dummy device 80x30
Calibrating delay loop... 1208.32 BogoMIPS (lpj=6041600)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0x80008200 - 0x80008258
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
futex hash table entries: 256 (order: -1, 3072 bytes)
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
Serial: AMBA PL011 UART driver
20080000.uart: ttyAMA0 at MMIO 0x20080000 (irq = 18, base_baud = 0) is a PL011 rev2
console [ttyAMA0] enabled
SCSI subsystem initialized
ssp-pl022 200c0000.spi: ARM PL022 driver, device ID: 0x00800022
ssp-pl022 200c0000.spi: mapped registers from 0x200c0000 to fe1c0000
ssp-pl022 200e0000.spi: ARM PL022 driver, device ID: 0x00800022
ssp-pl022 200e0000.spi: mapped registers from 0x200e0000 to fe1e0000
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
clocksource: Switched to clocksource arm,sp804
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
workingset: timestamp_bits=30 max_order=14 bucket_order=0
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
pl061_gpio 20140000.gpio_chip: PL061 GPIO chip @0x20140000 registered
pl061_gpio 20150000.gpio_chip: PL061 GPIO chip @0x20150000 registered
pl061_gpio 20160000.gpio_chip: PL061 GPIO chip @0x20160000 registered
pl061_gpio 20170000.gpio_chip: PL061 GPIO chip @0x20170000 registered
pl061_gpio 20180000.gpio_chip: PL061 GPIO chip @0x20180000 registered
pl061_gpio 20190000.gpio_chip: PL061 GPIO chip @0x20190000 registered
pl061_gpio 201a0000.gpio_chip: PL061 GPIO chip @0x201a0000 registered
pl061_gpio 201b0000.gpio_chip: PL061 GPIO chip @0x201b0000 registered
pl061_gpio 201c0000.gpio_chip: PL061 GPIO chip @0x201c0000 registered
pl061_gpio 201d0000.gpio_chip: PL061 GPIO chip @0x201d0000 registered
pl061_gpio 201e0000.gpio_chip: PL061 GPIO chip @0x201e0000 registered
pl061_gpio 201f0000.gpio_chip: PL061 GPIO chip @0x201f0000 registered
pl061_gpio 20200000.gpio_chip: PL061 GPIO chip @0x20200000 registered
pl061_gpio 20210000.gpio_chip: PL061 GPIO chip @0x20210000 registered
pl061_gpio 20220000.gpio_chip: PL061 GPIO chip @0x20220000 registered
pl061_gpio 20260000.gpio_chip: PL061 GPIO chip @0x20260000 registered
brd: module loaded
Spi id table Version 1.22
Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18
SPI nor flash boot mode is 3 Bytes
Spi(cs1): Block:64KB
Chip:16MB Name:"MX25L128XX"
spi size: 16MB
chip num: 1
3 cmdlinepart partitions found on MTD device hi_sfc
Creating 3 MTD partitions on "hi_sfc":
0x000000000000-0x000000100000 : "boot"
0x000000100000-0x000000400000 : "kernel"
0x000000400000-0x000001000000 : "rootfs"
random: fast init done
U-Boot 2010.06 (Jun 04 2015 - 14:17:45)
NAND: Check nand flash controller v610. found
Special NAND id table Version 1.36
Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
No NAND device found!!!
0 MiB
Check spi flash controller v350... Found
Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18
Spi(cs1): Block:64KB Chip:16MB Name:"MX25L128XX"
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
16384 KiB hi_sfc at 0:0 is now current device
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-4.9.37
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3100884 Bytes = 3 MiB
Load Address: 80008000
Entry Point: 80008000
Loading Kernel Image ... OK
OK
Starting kernel ...
Booting Linux on physical CPU 0x0
Linux version 4.9.37 (pub@BVT-SDK-SERVER1) (gcc version 6.2.1 20161016 (Hisilicon_v510_20171125) ) #1 Wed Jan 3 14:02:51 HKT 2018
CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
CPU: div instructions available: patching division code
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
OF: fdt:Machine model: Hisilicon HI3516A DEMO Board
Memory policy: Data cache writeback
CPU: All CPU(s) started in SVC mode.
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: mem=64M console=ttyAMA0,115200 root=/dev/mtdblock2 rootfstype=jffs2 mtdparts=hi_sfc:1M(boot),3M(kernel),12M(rootfs)
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 58488K/65536K available (4673K kernel code, 184K rwdata, 1032K rodata, 188K init, 252K bss, 7048K reserved, 0K cma-reserved)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xc4800000 - 0xff800000 ( 944 MB)
lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc0498980 (4675 kB)
.init : 0xc059d000 - 0xc05cc000 ( 188 kB)
.data : 0xc05cc000 - 0xc05fa160 ( 185 kB)
.bss : 0xc05fc000 - 0xc063b048 ( 253 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:16 nr_irqs:16 16
clocksource: arm,sp804: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns
sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns
Console: colour dummy device 80x30
Calibrating delay loop... 1208.32 BogoMIPS (lpj=6041600)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0x80008200 - 0x80008258
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
futex hash table entries: 256 (order: -1, 3072 bytes)
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
Serial: AMBA PL011 UART driver
20080000.uart: ttyAMA0 at MMIO 0x20080000 (irq = 18, base_baud = 0) is a PL011 rev2
console [ttyAMA0] enabled
SCSI subsystem initialized
ssp-pl022 200c0000.spi: ARM PL022 driver, device ID: 0x00800022
ssp-pl022 200c0000.spi: mapped registers from 0x200c0000 to fe1c0000
ssp-pl022 200e0000.spi: ARM PL022 driver, device ID: 0x00800022
ssp-pl022 200e0000.spi: mapped registers from 0x200e0000 to fe1e0000
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
clocksource: Switched to clocksource arm,sp804
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
workingset: timestamp_bits=30 max_order=14 bucket_order=0
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
pl061_gpio 20140000.gpio_chip: PL061 GPIO chip @0x20140000 registered
pl061_gpio 20150000.gpio_chip: PL061 GPIO chip @0x20150000 registered
pl061_gpio 20160000.gpio_chip: PL061 GPIO chip @0x20160000 registered
pl061_gpio 20170000.gpio_chip: PL061 GPIO chip @0x20170000 registered
pl061_gpio 20180000.gpio_chip: PL061 GPIO chip @0x20180000 registered
pl061_gpio 20190000.gpio_chip: PL061 GPIO chip @0x20190000 registered
pl061_gpio 201a0000.gpio_chip: PL061 GPIO chip @0x201a0000 registered
pl061_gpio 201b0000.gpio_chip: PL061 GPIO chip @0x201b0000 registered
pl061_gpio 201c0000.gpio_chip: PL061 GPIO chip @0x201c0000 registered
pl061_gpio 201d0000.gpio_chip: PL061 GPIO chip @0x201d0000 registered
pl061_gpio 201e0000.gpio_chip: PL061 GPIO chip @0x201e0000 registered
pl061_gpio 201f0000.gpio_chip: PL061 GPIO chip @0x201f0000 registered
pl061_gpio 20200000.gpio_chip: PL061 GPIO chip @0x20200000 registered
pl061_gpio 20210000.gpio_chip: PL061 GPIO chip @0x20210000 registered
pl061_gpio 20220000.gpio_chip: PL061 GPIO chip @0x20220000 registered
pl061_gpio 20260000.gpio_chip: PL061 GPIO chip @0x20260000 registered
brd: module loaded
Spi id table Version 1.22
Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18
SPI nor flash boot mode is 3 Bytes
Spi(cs1): Block:64KB
Chip:16MB Name:"MX25L128XX"
spi size: 16MB
chip num: 1
3 cmdlinepart partitions found on MTD device hi_sfc
Creating 3 MTD partitions on "hi_sfc":
0x000000000000-0x000000100000 : "boot"
0x000000100000-0x000000400000 : "kernel"
0x000000400000-0x000001000000 : "rootfs"
random: fast init done
我来回答
回答2个
时间排序
认可量排序
认可0
认可0
或将文件直接拖到这里
悬赏:
E币
网盘
* 网盘链接:
* 提取码:
悬赏:
E币
Markdown 语法
- 加粗**内容**
- 斜体*内容*
- 删除线~~内容~~
- 引用> 引用内容
- 代码`代码`
- 代码块```编程语言↵代码```
- 链接[链接标题](url)
- 无序列表- 内容
- 有序列表1. 内容
- 缩进内容
- 图片![alt](url)
相关问答
-
2021-03-18 19:48:30
-
2015-06-16 10:53:32
-
2020-07-31 17:16:33
-
2019-08-29 09:37:01
-
2017-06-21 15:59:45
-
2008-08-02 16:47:25
-
2017-01-12 19:58:05
-
2015-12-23 16:56:34
-
2016-06-14 23:57:07
-
2010-07-23 16:56:24
-
2022-12-27 18:27:18
-
2020-11-25 16:29:48
-
2016-03-19 15:34:10
-
2018-12-08 11:01:45
-
2015-03-14 15:03:06
-
2019-10-10 22:07:55
-
2020-05-28 10:30:33
-
2016-07-07 15:06:21
-
2019-09-10 11:05:35
无更多相似问答 去提问
点击登录
-- 积分
-- E币
提问
—
收益
—
被采纳
—
我要提问
切换马甲
上一页
下一页
悬赏问答
-
5Hi3516CV610 如何使用SD卡升级固件
-
5cat /dev/logmpp 报错 <3>[ vi] [func]:vi_send_frame_node [line]:99 [info]:vi pic queue is full!
-
50如何获取vpss chn的图像修改后发送至vo
-
5FPGA通过Bt1120传YUV422数据过来,vi接收不到数据——3516dv500
-
50SS928 运行PQtools 拼接 推到设备里有一半画面会异常
-
53536AV100的sample_vdec输出到CVBS显示
-
10海思板子mpp怎么在vi阶段改变视频数据尺寸
-
10HI3559AV100 多摄像头同步模式
-
9海思ss928单路摄像头vio中加入opencv处理并显示
-
10EB-RV1126-BC-191板子运行自己编码的程序
举报反馈
举报类型
- 内容涉黄/赌/毒
- 内容侵权/抄袭
- 政治相关
- 涉嫌广告
- 侮辱谩骂
- 其他
详细说明
提醒
你的问题还没有最佳答案,是否结题,结题后将扣除20%的悬赏金
取消
确认
提醒
你的问题还没有最佳答案,是否结题,结题后将根据回答情况扣除相应悬赏金(1回答=1E币)
取消
确认