2189
- 收藏
- 点赞
- 分享
- 举报
Hi3531启动时报错
各位好:
产品用Hi3531芯片的板子,大都启动没有问题可以正常进入系统,但有几块板子启动时报错如下:
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:128 nr_irqs:128 128
sched_clock: 32 bits at 155MHz, resolution 6ns, wraps every 27709ms
Console: colour dummy device 80x30
Calibrating delay loop... 1849.75 BogoMIPS (lpj=9248768)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
CPU1: Booted secondary processor
Brought up 2 CPUs
SMP: Total of 2 processors activated (3706.06 BogoMIPS).
NET: Registered protocol family 16
Serial: AMBA PL011 UART driver
uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 40) is a PL011 rev2
console [ttyAMA0] enabled
uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 41) is a PL011 rev2
uart:2: ttyAMA2 at MMIO 0x200a0000 (irq = 42) is a PL011 rev2
uart:3: ttyAMA3 at MMIO 0x200b0000 (irq = 43) is a PL011 rev2
//以下开始报出的错误信息
Unhandled fault: alignment exception (0x011) at 0xffff0037
Internal error: : 11 [#1] SMP
Modules linked in:
CPU: 1 Not tainted (3.0.8 #26)
PC is at acct_process+0x48/0xc8
LR is at acct_process+0x20/0xc8
pc : [] lr : [] psr: a0000013
sp : df9c9f70 ip : df9c9f70 fp : df9c9f94
r10: 00000000 r9 : 00000001 r8 : ffff002f
r7 : 00000000 r6 : c06ee008 r5 : df401080 r4 : df9aabc0
r3 : 00000000 r2 : 00000000 r1 : df9c9f70 r0 : c06ee008
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c53c7f Table: 8000404a DAC: 00000015
PC: 0xc008fd48:
fd48 e0922002 e3a00000 e0a33003 e3a01000 e1500002 e0d11003 e24cc001 bafffff7
fd68 e14b07dc e1a0cb8c e50b809c e7f62453 e182c00c eaffff1c e1a0c00d e92dd9f8
fd88 e24cb004 e1a0100d e3c10d7f e3c0303f e593000c ebff8ae1 e2505000 089da9f8
fda8 e30e6008 e34c606e e3a07000 e5958024 e30e0008 e34c006e e3580000 0a000016
fdc8 e5982008 e3520000 0a000013 eb12e71b e5984008 e3540000 e284301c 0a000012
fde8 e1931f9f e2811001 e1832f91 e3320000 1afffffa f57ff05f e5867000 f57ff04f
fe08 e320f004 e1a00008 e1a01005 e1a02004 ebfffea9 e1a00004 eb00fd1b e595501c
fe28 e3550000 1affffe0 e89da9f8 f57ff05f e5864000 f57ff04f e320f004 eafffff6
LR: 0xc008fd20:
fd20 e1520000 e0d38001 a1a03001 a3a0c45f aa00000f e51b809c e1a02000 e1a03001
fd40 e3a0c0be e14b07fc e0922002 e3a00000 e0a33003 e3a01000 e1500002 e0d11003
fd60 e24cc001 bafffff7 e14b07dc e1a0cb8c e50b809c e7f62453 e182c00c eaffff1c
fd80 e1a0c00d e92dd9f8 e24cb004 e1a0100d e3c10d7f e3c0303f e593000c ebff8ae1
fda0 e2505000 089da9f8 e30e6008 e34c606e e3a07000 e5958024 e30e0008 e34c006e
bio: create slab at 0
controller0, config base:0x20800000, mem size:0x800000
controhler1, config base:0x20810000, mem size:0x800000
pci 0000:00:00.0: [19e5:3531] type 1 class 0x000604
正常启动进入系统的板子输出是这样的:
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:128 nr_irqs:128 128
sched_clock: 32 bits at 155MHz, resolution 6ns, wraps every 27709ms
Console: colour dummy device 80x30
Calibrating delay loop... 1849.75 BogoMIPS (lpj=9248768)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
CPU1: Booted secondary processor
Brought up 2 CPUs
SMP: Total of 2 processors activated (3706.06 BogoMIPS).
NET: Registered protocol family 16
Serial: AMBA PL011 UART driver
uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 40) is a PL011 rev2
console [ttyAMA0] enabled
uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 41) is a PL011 rev2
uart:2: ttyAMA2 at MMIO 0x200a0000 (irq = 42) is a PL011 rev2
uart:3: ttyAMA3 at MMIO 0x200b0000 (irq = 43) is a PL011 rev2
bio: create slab at 0
controller0, config base:0x20800000, mem size:0x800000
controller1, config base:0x20810000, mem size:0x800000
PCI: bus0: Fast back to back transfers disabled
PCI: bus1: Fast back to back transfers enabled
PCI: bus2: Fast back to back transfers disabled
PCI: bus3: Fast back to back transfers enabled
pci 0000:02:00.0: BAR 0: assigned [mem 0x60000000-0x607fffff pref]
pci 0000:02:00.0: BAR 0: set to [mem 0x60000000-0x607fffff pref] (PCI address [0x60000000-0x607fffff])
pci 0000:02:00.0: BAR 1: assigned [mem 0x60800000-0x6080ffff]
pci 0000:02:00.0: BAR 1: set to [mem 0x60800000-0x6080ffff] (PCI address [0x60800000-0x6080ffff])
pci 0000:02:00.0: BAR 6: assigned [mem 0x60810000-0x6081ffff pref]
pci 0000:02:00.0: PCI bridge to [bus 03-03]
pci 0000:02:00.0: bridge window [io disabled]
pci 0000:02:00.0: bridge window [mem disabled]
pci 0000:02:00.0: bridge window [mem pref disabled]
pci 0000:00:00.0: BAR 0: assigned [mem 0x30000000-0x307fffff pref]
pci 0000:00:00.0: BAR 0: set to [mem 0x30000000-0x307fffff pref] (PCI address [0x30000000-0x307fffff])
pci 0000:00:00.0: BAR 1: assigned [mem 0x30800000-0x3080ffff]
pci 0000:00:00.0: BAR 1: set to [mem 0x30800000-0x3080ffff] (PCI address [0x30800000-0x3080ffff])
pci 0000:00:00.0: BAR 6: assigned [mem 0x30810000-0x3081ffff pref]
bio: create slab at 0,报出的板子没有执行到这句输出,就开输出错误信息了,请问各位是内存焊接问题,还是3531没有焊接好呢?
产品用Hi3531芯片的板子,大都启动没有问题可以正常进入系统,但有几块板子启动时报错如下:
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:128 nr_irqs:128 128
sched_clock: 32 bits at 155MHz, resolution 6ns, wraps every 27709ms
Console: colour dummy device 80x30
Calibrating delay loop... 1849.75 BogoMIPS (lpj=9248768)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
CPU1: Booted secondary processor
Brought up 2 CPUs
SMP: Total of 2 processors activated (3706.06 BogoMIPS).
NET: Registered protocol family 16
Serial: AMBA PL011 UART driver
uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 40) is a PL011 rev2
console [ttyAMA0] enabled
uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 41) is a PL011 rev2
uart:2: ttyAMA2 at MMIO 0x200a0000 (irq = 42) is a PL011 rev2
uart:3: ttyAMA3 at MMIO 0x200b0000 (irq = 43) is a PL011 rev2
//以下开始报出的错误信息
Unhandled fault: alignment exception (0x011) at 0xffff0037
Internal error: : 11 [#1] SMP
Modules linked in:
CPU: 1 Not tainted (3.0.8 #26)
PC is at acct_process+0x48/0xc8
LR is at acct_process+0x20/0xc8
pc : [
sp : df9c9f70 ip : df9c9f70 fp : df9c9f94
r10: 00000000 r9 : 00000001 r8 : ffff002f
r7 : 00000000 r6 : c06ee008 r5 : df401080 r4 : df9aabc0
r3 : 00000000 r2 : 00000000 r1 : df9c9f70 r0 : c06ee008
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c53c7f Table: 8000404a DAC: 00000015
PC: 0xc008fd48:
fd48 e0922002 e3a00000 e0a33003 e3a01000 e1500002 e0d11003 e24cc001 bafffff7
fd68 e14b07dc e1a0cb8c e50b809c e7f62453 e182c00c eaffff1c e1a0c00d e92dd9f8
fd88 e24cb004 e1a0100d e3c10d7f e3c0303f e593000c ebff8ae1 e2505000 089da9f8
fda8 e30e6008 e34c606e e3a07000 e5958024 e30e0008 e34c006e e3580000 0a000016
fdc8 e5982008 e3520000 0a000013 eb12e71b e5984008 e3540000 e284301c 0a000012
fde8 e1931f9f e2811001 e1832f91 e3320000 1afffffa f57ff05f e5867000 f57ff04f
fe08 e320f004 e1a00008 e1a01005 e1a02004 ebfffea9 e1a00004 eb00fd1b e595501c
fe28 e3550000 1affffe0 e89da9f8 f57ff05f e5864000 f57ff04f e320f004 eafffff6
LR: 0xc008fd20:
fd20 e1520000 e0d38001 a1a03001 a3a0c45f aa00000f e51b809c e1a02000 e1a03001
fd40 e3a0c0be e14b07fc e0922002 e3a00000 e0a33003 e3a01000 e1500002 e0d11003
fd60 e24cc001 bafffff7 e14b07dc e1a0cb8c e50b809c e7f62453 e182c00c eaffff1c
fd80 e1a0c00d e92dd9f8 e24cb004 e1a0100d e3c10d7f e3c0303f e593000c ebff8ae1
fda0 e2505000 089da9f8 e30e6008 e34c606e e3a07000 e5958024 e30e0008 e34c006e
bio: create slab
controller0, config base:0x20800000, mem size:0x800000
controhler1, config base:0x20810000, mem size:0x800000
pci 0000:00:00.0: [19e5:3531] type 1 class 0x000604
正常启动进入系统的板子输出是这样的:
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:128 nr_irqs:128 128
sched_clock: 32 bits at 155MHz, resolution 6ns, wraps every 27709ms
Console: colour dummy device 80x30
Calibrating delay loop... 1849.75 BogoMIPS (lpj=9248768)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
CPU1: Booted secondary processor
Brought up 2 CPUs
SMP: Total of 2 processors activated (3706.06 BogoMIPS).
NET: Registered protocol family 16
Serial: AMBA PL011 UART driver
uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 40) is a PL011 rev2
console [ttyAMA0] enabled
uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 41) is a PL011 rev2
uart:2: ttyAMA2 at MMIO 0x200a0000 (irq = 42) is a PL011 rev2
uart:3: ttyAMA3 at MMIO 0x200b0000 (irq = 43) is a PL011 rev2
bio: create slab
controller0, config base:0x20800000, mem size:0x800000
controller1, config base:0x20810000, mem size:0x800000
PCI: bus0: Fast back to back transfers disabled
PCI: bus1: Fast back to back transfers enabled
PCI: bus2: Fast back to back transfers disabled
PCI: bus3: Fast back to back transfers enabled
pci 0000:02:00.0: BAR 0: assigned [mem 0x60000000-0x607fffff pref]
pci 0000:02:00.0: BAR 0: set to [mem 0x60000000-0x607fffff pref] (PCI address [0x60000000-0x607fffff])
pci 0000:02:00.0: BAR 1: assigned [mem 0x60800000-0x6080ffff]
pci 0000:02:00.0: BAR 1: set to [mem 0x60800000-0x6080ffff] (PCI address [0x60800000-0x6080ffff])
pci 0000:02:00.0: BAR 6: assigned [mem 0x60810000-0x6081ffff pref]
pci 0000:02:00.0: PCI bridge to [bus 03-03]
pci 0000:02:00.0: bridge window [io disabled]
pci 0000:02:00.0: bridge window [mem disabled]
pci 0000:02:00.0: bridge window [mem pref disabled]
pci 0000:00:00.0: BAR 0: assigned [mem 0x30000000-0x307fffff pref]
pci 0000:00:00.0: BAR 0: set to [mem 0x30000000-0x307fffff pref] (PCI address [0x30000000-0x307fffff])
pci 0000:00:00.0: BAR 1: assigned [mem 0x30800000-0x3080ffff]
pci 0000:00:00.0: BAR 1: set to [mem 0x30800000-0x3080ffff] (PCI address [0x30800000-0x3080ffff])
pci 0000:00:00.0: BAR 6: assigned [mem 0x30810000-0x3081ffff pref]
bio: create slab
我来回答
回答1个
时间排序
认可量排序
认可0
或将文件直接拖到这里
悬赏:
E币
网盘
* 网盘链接:
* 提取码:
悬赏:
E币
Markdown 语法
- 加粗**内容**
- 斜体*内容*
- 删除线~~内容~~
- 引用> 引用内容
- 代码`代码`
- 代码块```编程语言↵代码```
- 链接[链接标题](url)
- 无序列表- 内容
- 有序列表1. 内容
- 缩进内容
- 图片
相关问答
-
2020-12-20 09:28:01
-
2023-01-28 14:07:03
-
2016-12-13 09:28:16
-
2015-08-10 13:59:20
-
2015-07-13 11:05:48
-
2015-11-30 13:41:56
-
2019-03-04 13:26:34
-
2017-02-15 09:46:29
-
2020-11-21 17:58:06
-
2017-04-27 19:23:23
-
2018-12-12 13:48:17
-
2017-11-24 09:29:06
-
2013-11-12 17:56:33
-
2015-04-05 11:00:16
-
12016-04-12 16:51:45
-
12016-01-18 23:22:46
-
2017-03-25 23:36:00
-
2018-07-05 14:24:36
-
2016-08-16 15:11:59
无更多相似问答 去提问

点击登录
-- 积分
-- E币
提问
—
收益
—
被采纳
—
我要提问
切换马甲
上一页
下一页
悬赏问答
-
53519dv500接lvds的sensor mn34120,图像出现很多竖线,sensor板接以前的3519v101没问题
-
103403外接hdmi口1024*600显示屏报错
-
5SS928点DC camera的6946,全屏紫色
-
5hi3519 的 网络传输的MTU值可以修改到比1500大嘛?
-
10WS73V100星闪扫描不到设备sle
-
5SS928/SD3403 录像失败 venc stream time out, exit thread; venc 2 stream buffer is full
-
10Hi3516DV500无法运行PQTool软件
-
10君正T23+1084带TF卡插卡(给该主板适配TF卡驱动,电机驱动,适配GPIO)
-
5Hi3536A从vpss获取1080分辨率的yuv数据异常
-
10谁有RV1126 最新版本SDK卖吗?
举报反馈
举报类型
- 内容涉黄/赌/毒
- 内容侵权/抄袭
- 政治相关
- 涉嫌广告
- 侮辱谩骂
- 其他
详细说明
提醒
你的问题还没有最佳答案,是否结题,结题后将扣除20%的悬赏金
取消
确认
提醒
你的问题还没有最佳答案,是否结题,结题后将根据回答情况扣除相应悬赏金(1回答=1E币)
取消
确认