3597
- 收藏
- 点赞
- 分享
- 举报
HI3518A+RT3070(WIFI)问题
按照网上诸贤的方法编译,出现如下问题:
# insmod rt3070sta.ko
rtusb init rt2870 --->
===>rt2870_probe()!
--> RTMPAllocAdapterBlock
=== pAd = c5088000, size = 509936 ===
--> RTMPAllocTxRxRingMemory
<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
NumEndpoints=7
BULK IN MaxPacketSize = 512
EP address = 0x81
BULK OUT MaxPacketSize = 512
EP address = 0x 1
BULK OUT MaxPacketSize = 512
EP address = 0x 2
BULK OUT MaxPacketSize = 512
EP address = 0x 3
BULK OUT MaxPacketSize = 512
EP address = 0x 4
BULK OUT MaxPacketSize = 512
EP address = 0x 5
BULK OUT MaxPacketSize = 512
EP address = 0x 6
STA Driver version-2.5.0.1
time out is 30#
#
#
#
#
#
#
#
#
#
RTUSB_VendorRequest failed(-110),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x1000,pAd->Flags=0x0
time out is 30#
#
#
#
#
#
#
#
#
#
RTUSB_VendorRequest failed(-110),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x580,pAd->Flags=0x0
NVM is EFUSE
Allocate a net device with private data size=0!
Allocate net device ops success!
The name of the new ra interface is ra0...
RtmpOSNetDevAttach()--->
<---RtmpOSNetDevAttach(), ret=0
<===rt2870_probe()!
usbcore: registered new interface driver rt2870
输入:
# ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:00:23:34:45:66
inet addr:192.168.0.30 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::200:23ff:fe34:4566/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1313 errors:0 dropped:0 overruns:0 frame:0
TX packets:55 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1156067 (1.1 MiB) TX bytes:7566 (7.3 KiB)
Interrupt:12
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
ra0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
输入:
# ifconfig ra0 up
Allocate 8192 memory for BA reordering
time out is 30#
#
#
#
#
#
#
#
#
#
RTUSB_VendorRequest failed(-110),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x1000,pAd->Flags=0x0
MAC_CSR0 [ Ver:Rev=0xc0555e20]
rtmp_ee_efuse_read16
time out is 30#
#
#
#
#
#
#
#
#
#
RTUSB_VendorRequest failed(-110),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x580,pAd->Flags=0x0
time out is 30#
不停地输出。
跟踪程序,发现问题出现在这里:
do {
RTUSB_CONTROL_MSG(pObj->pUsb_Dev, 0, Request, RequestType, Value, Index, pAd->UsbVendorReqBuf, TransferBufferLength, CONTROL_TIMEOUT_JIFFIES, RET);
if (RET < 0) {
DBGPRINT(RT_DEBUG_OFF, ("#\n"));
if (RET == RTMP_USB_CONTROL_MSG_ENODEV)
{
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_NIC_NOT_EXIST); break;
}
RetryCount++;
RTMPusecDelay(5000); /* wait for 5ms*/
}
} while((RET < 0) && (RetryCount < MAX_VENDOR_REQ_RETRY_COUNT));
好象是与USB<--->RT3070通迅失常,问题出在RTUSB_CONTROL_MSG上,不知何解?
# insmod rt3070sta.ko
rtusb init rt2870 --->
===>rt2870_probe()!
--> RTMPAllocAdapterBlock
=== pAd = c5088000, size = 509936 ===
--> RTMPAllocTxRxRingMemory
<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
NumEndpoints=7
BULK IN MaxPacketSize = 512
EP address = 0x81
BULK OUT MaxPacketSize = 512
EP address = 0x 1
BULK OUT MaxPacketSize = 512
EP address = 0x 2
BULK OUT MaxPacketSize = 512
EP address = 0x 3
BULK OUT MaxPacketSize = 512
EP address = 0x 4
BULK OUT MaxPacketSize = 512
EP address = 0x 5
BULK OUT MaxPacketSize = 512
EP address = 0x 6
STA Driver version-2.5.0.1
time out is 30#
#
#
#
#
#
#
#
#
#
RTUSB_VendorRequest failed(-110),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x1000,pAd->Flags=0x0
time out is 30#
#
#
#
#
#
#
#
#
#
RTUSB_VendorRequest failed(-110),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x580,pAd->Flags=0x0
NVM is EFUSE
Allocate a net device with private data size=0!
Allocate net device ops success!
The name of the new ra interface is ra0...
RtmpOSNetDevAttach()--->
<---RtmpOSNetDevAttach(), ret=0
<===rt2870_probe()!
usbcore: registered new interface driver rt2870
输入:
# ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:00:23:34:45:66
inet addr:192.168.0.30 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::200:23ff:fe34:4566/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1313 errors:0 dropped:0 overruns:0 frame:0
TX packets:55 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1156067 (1.1 MiB) TX bytes:7566 (7.3 KiB)
Interrupt:12
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
ra0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
输入:
# ifconfig ra0 up
Allocate 8192 memory for BA reordering
time out is 30#
#
#
#
#
#
#
#
#
#
RTUSB_VendorRequest failed(-110),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x1000,pAd->Flags=0x0
MAC_CSR0 [ Ver:Rev=0xc0555e20]
rtmp_ee_efuse_read16
time out is 30#
#
#
#
#
#
#
#
#
#
RTUSB_VendorRequest failed(-110),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x580,pAd->Flags=0x0
time out is 30#
不停地输出。
跟踪程序,发现问题出现在这里:
do {
RTUSB_CONTROL_MSG(pObj->pUsb_Dev, 0, Request, RequestType, Value, Index, pAd->UsbVendorReqBuf, TransferBufferLength, CONTROL_TIMEOUT_JIFFIES, RET);
if (RET < 0) {
DBGPRINT(RT_DEBUG_OFF, ("#\n"));
if (RET == RTMP_USB_CONTROL_MSG_ENODEV)
{
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_NIC_NOT_EXIST); break;
}
RetryCount++;
RTMPusecDelay(5000); /* wait for 5ms*/
}
} while((RET < 0) && (RetryCount < MAX_VENDOR_REQ_RETRY_COUNT));
好象是与USB<--->RT3070通迅失常,问题出在RTUSB_CONTROL_MSG上,不知何解?
我来回答
回答0个
时间排序
认可量排序
暂无数据
或将文件直接拖到这里
悬赏:
E币
网盘
* 网盘链接:
* 提取码:
悬赏:
E币
Markdown 语法
- 加粗**内容**
- 斜体*内容*
- 删除线~~内容~~
- 引用> 引用内容
- 代码`代码`
- 代码块```编程语言↵代码```
- 链接[链接标题](url)
- 无序列表- 内容
- 有序列表1. 内容
- 缩进内容
- 图片![alt](url)
相关问答
-
2015-04-03 15:38:12
-
2015-04-03 15:47:22
-
02017-04-10 17:01:22
-
62017-03-28 18:41:46
-
2015-04-03 16:14:23
-
2014-04-08 16:12:33
-
2017-08-12 11:08:23
-
2017-07-20 20:47:54
-
2014-12-02 10:42:38
-
2015-08-05 14:42:12
-
2015-05-31 11:06:32
-
2016-10-14 11:48:23
-
2015-05-06 22:25:07
-
2015-10-15 16:46:09
-
2016-06-03 10:26:59
-
1812017-04-27 16:00:34
-
2015-07-17 17:10:12
-
2015-09-21 09:38:32
-
2019-10-11 09:44:50
-
2017-03-27 16:46:23
更多相似问答
点击登录
-- 积分
-- E币
提问
—
收益
—
被采纳
—
我要提问
切换马甲
上一页
下一页
悬赏问答
-
5Hi3516CV610 如何使用SD卡升级固件
-
5cat /dev/logmpp 报错 <3>[ vi] [func]:vi_send_frame_node [line]:99 [info]:vi pic queue is full!
-
50如何获取vpss chn的图像修改后发送至vo
-
5FPGA通过Bt1120传YUV422数据过来,vi接收不到数据——3516dv500
-
50SS928 运行PQtools 拼接 推到设备里有一半画面会异常
-
53536AV100的sample_vdec输出到CVBS显示
-
10海思板子mpp怎么在vi阶段改变视频数据尺寸
-
10HI3559AV100 多摄像头同步模式
-
9海思ss928单路摄像头vio中加入opencv处理并显示
-
10EB-RV1126-BC-191板子运行自己编码的程序
举报反馈
举报类型
- 内容涉黄/赌/毒
- 内容侵权/抄袭
- 政治相关
- 涉嫌广告
- 侮辱谩骂
- 其他
详细说明
提醒
你的问题还没有最佳答案,是否结题,结题后将扣除20%的悬赏金
取消
确认
提醒
你的问题还没有最佳答案,是否结题,结题后将根据回答情况扣除相应悬赏金(1回答=1E币)
取消
确认