MT7620内核启动报错

U-Boot 1.1.3 (Jul 20 2015 - 15:33:02)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb0000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: ef 40 18 0 0 (40180000)
find flash: W25Q128BV
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jul 20 2015  Time:15:33:02
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes

============================================

########## WEB FAILSAFE MODE ###########

1.Press GPIO_1  for more than 5 seconds
  to run web failsafe mode
GPIO_1 is pressed for:  0 second(s)
Catution: GPIO_1 wasn't pressed or not long enough!
Continuing normal boot...
============================================


Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   5: Load ART file then write to Flash via TFTP!!!
   6: Enter to web failsafe httpd!!!
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
0
   
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
   Image Name:   MIPS OpenWrt Linux-3.10.49
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1075933 Bytes =  1 MB
   Load Address: 80000000
   Entry Point:  80000000
raspi_read: from:50040 len:106add
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 3.10.49 ([email]openwrt@localhost.localdomain[/email]) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r43770) ) #4 Wed Sep 23 14:16:59 CST 2015
[    0.000000] Board has DDR2
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: Ralink MT7620A ver:2 eco:3
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019650 (MIPS 24KEc)
[    0.000000] MIPS: machine is Ralink MT7620a + MT7610e evaluation board
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00078eef
[    0.000000] Readback ErrCtl register=00078eef
[    0.000000] Memory: 61512k/65536k available (2380k kernel code, 4024k reserved, 592k data, 224k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 580MHz
[    0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.060000] pid_max: default: 32768 minimum: 301
[    0.060000] Mount-cache hash table entries: 512
[    0.070000] pinctrl core: initialized pinctrl subsystem
[    0.080000] NET: Registered protocol family 16
[    0.450000] PCIE0 no card, disable it(RST&CLK)
[    0.460000] bio: create slab at 0
[    0.470000] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.480000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.490000] PCI host bridge to bus 0000:00
[    0.500000] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[    0.510000] pci_bus 0000:00: root bus resource [io  0x10160000-0x1016ffff]
[    0.520000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.530000] Switching to clocksource MIPS
[    0.540000] NET: Registered protocol family 2
[    0.540000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.550000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.560000] TCP: Hash tables configured (established 512 bind 512)
[    0.580000] TCP: reno registered
[    0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.610000] NET: Registered protocol family 1
[    0.620000] rt-timer 10000100.timer: maximum frequncy is 2441Hz
[    0.650000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.660000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.680000] msgmni has been set to 120
[    0.690000] io scheduler noop registered
[    0.690000] io scheduler deadline registered (default)
[    0.700000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.720000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A
[    0.730000] console [ttyS0] enabled, bootconsole disabled
[    0.730000] console [ttyS0] enabled, bootconsole disabled
[    0.760000] m25p80 spi32766.0: found w25q128, expected en25q64
[    0.770000] m25p80 spi32766.0: w25q128 (16384 Kbytes)
[    0.780000] 4 ofpart partitions found on MTD device spi32766.0
[    0.790000] Creating 4 MTD partitions on "spi32766.0":
[    0.800000] 0x000000000000-0x000000030000 : "u-boot"
[    0.820000] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.830000] 0x000000040000-0x000000050000 : "factory"
[    0.840000] 0x000000050000-0x000000800000 : "firmware"
[    0.850000] 0x000000156b1d-0x000000800000 : "rootfs"
[    0.860000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.890000] mtd: device 4 (rootfs) set to be root filesystem
[    0.900000] mtd: partition "rootfs_data" created automatically, ofs=0x380000, len=0x480000
[    0.920000] 0x000000380000-0x000000800000 : "rootfs_data"
[    0.930000] libphy: mdio: probed
[    0.940000] mdio_bus mdio-bus: cannot get PHY at address 5
[    0.950000] ralink_soc_eth 10100000.ethernet: connected port 4 to PHY at mdio-bus:04 [uid=03a2940d, driver=Generic PHY]
[    0.970000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver
[    0.990000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
[    1.000000] rt3xxx-usbphy usbphy.3: loaded
[    1.010000] rt2880_wdt 10000120.watchdog: Initialized
[    1.020000] TCP: cubic registered
[    1.030000] NET: Registered protocol family 17
[    1.040000] 8021q: 802.1Q VLAN Support v1.8
[    1.060000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    1.070000] Freeing unused kernel memory: 224K (802e8000 - 80320000)
procd: Console is alive
procd: - watchdog -
[    4.380000] usbcore: registered new interface driver usbfs
[    4.390000] usbcore: registered new interface driver hub
[    4.400000] usbcore: registered new device driver usb
[    4.420000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.430000] ehci-platform: EHCI generic platform driver
[    4.640000] rt3xxx-usbphy usbphy.3: remote usb device wakeup disabled
[    4.650000] rt3xxx-usbphy usbphy.3: UTMI 16bit 30MHz
[    4.660000] ehci-platform 101c0000.ehci: EHCI Host Controller
[    4.670000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[    4.690000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[    4.720000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[    4.730000] hub 1-0:1.0: USB hub found
[    4.740000] hub 1-0:1.0: 1 port detected
[    4.750000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.760000] ohci-platform 101c1000.ohci: Generic Platform OHCI Controller
[    4.770000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[    4.790000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[    4.860000] hub 2-0:1.0: USB hub found
[    4.870000] hub 2-0:1.0: 1 port detected
procd: - preinit -
[    5.060000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    5.370000] 8021q: adding VLAN 0 to HW filter on device eth0
[    5.390000] hub 1-1:1.0: USB hub found
[    5.400000] hub 1-1:1.0: 4 ports detected
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    6.970000] ralink_soc_eth 10100000.ethernet eth0: port 4 link up (1000Mbps/Full duplex)
[    6.970000] CPU 0 Unable to handle kernel paging request at virtual address 0000010c, epc == 800d047c, ra == 8018faa8
[    6.970000] Oops[#1]:
[    6.970000] CPU: 0 PID: 4 Comm: kworker/0:0 Not tainted 3.10.49 #4
[    6.970000] Workqueue: events phy_state_machine
[    6.970000] task: 83828c90 ti: 8383e000 task.ti: 8383e000
[    6.970000] $ 0   : 00000000 0000006e 00000000 00000000
[    6.970000] $ 4   : 802e2ef4 802dffc0 802cf890 00000014
[    6.970000] $ 8   : 00000029 30312820 624d3030 462f7370
[    6.970000] $12   : 00000000 00000001 00000000 43495645
[    6.970000] $16   : 00000005 8380a800 00000008 8380abc0
[    6.970000] $20   : 8380abc0 00000001 00000064 000003e8
[    6.970000] $24   : 00000003 800649c0                  
[    6.970000] $28   : 8383e000 8383fe00 0000000a 8018faa8
[    6.970000] Hi    : 00000000
[    6.970000] Lo    : ec4e4000
[    6.970000] epc   : 800d047c fe_phy_link_adjust+0x78/0x13c
[    6.970000]     Not tainted
[    6.970000] ra    : 8018faa8 phy_state_machine+0x39c/0x40c
[    6.970000] Status: 1100a402 KERNEL EXL
[    6.970000] Cause : 40808008
[    6.970000] BadVA : 0000010c
[    6.970000] PrId  : 00019650 (MIPS 24KEc)
[    6.970000] Modules linked in: leds_gpio ohci_hcd ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common
[    6.970000] Process kworker/0:0 (pid: 4, threadinfo=8383e000, task=83828c90, tls=00000000)
[    6.970000] Stack : 83927c00 83927c28 00000001 80147674 83927f3c 00000020 802cf880 83927e00
          83927f74 00000000 00000000 802d0000 802cf890 8018faa8 802cfd70 801902bc
          83828c90 8009dc10 83818980 83927f3c 802cf880 802d0000 81087600 801a5f14
          802d62d8 8000c408 802cfd70 802cf880 802d0000 802cf880 83818980 83818980
          802cf880 802cf880 802d0000 00000001 802937e8 83818998 802d0000 8024e304
          ...
[    6.970000] Call Trace:
[    6.970000] [<800d047c>] fe_phy_link_adjust+0x78/0x13c
[    6.970000] [<8018faa8>] phy_state_machine+0x39c/0x40c
[    6.970000] [<801a5f14>] process_one_work+0x268/0x3d4
[    6.970000] [<8024e304>] worker_thread+0x278/0x400
[    6.970000] [<80136660>] kthread+0xb0/0xb8
[    6.970000] [<80004878>] ret_from_kernel_thread+0x14/0x1c
[    6.970000]
[    6.970000]
Code: 10400025  00001021  8c830000 <8c66010c> 10c00008  8c6500fc  8c890060  8c680100  15280004
[    7.380000] ---[ end trace e55cdc53f47faf43 ]---
[    7.400000] CPU 0 Unable to handle kernel paging request at virtual address fffffff0, epc == 801367d4, ra == 8024ec80
[    7.400000] Oops[#2]:
[    7.400000] CPU: 0 PID: 4 Comm: kworker/0:0 Tainted: G      D      3.10.49 #4
[    7.400000] task: 83828c90 ti: 8383e000 task.ti: 8383e000
[    7.400000] $ 0   : 00000000 00000001 00000000 00000001
[    7.400000] $ 4   : 83828c90 00000000 802cfd70 00000001
[    7.400000] $ 8   : 13d2536e 00000000 00000000 00000000
[    7.400000] $12   : 00000014 00000001 800a0009 00000001
[    7.400000] $16   : 00000000 00000001 802d0000 83828000
[    7.400000] $20   : 802cfd70 83828de8 83828c88 802cfd70
[    7.400000] $24   : 802af00c 8009dc3c                  
[    7.400000] $28   : 8383e000 8383fbc0 00000020 8024ec80
[    7.400000] Hi    : 00000001
[    7.400000] Lo    : b9130a00
[    7.400000] epc   : 801367d4 kthread_data+0x4/0xc
[    7.400000]     Tainted: G      D     
[    7.400000] ra    : 8024ec80 wq_worker_sleeping+0x14/0xf4
[    7.400000] Status: 1100a402 KERNEL EXL
[    7.400000] Cause : 80800008
[    7.400000] BadVA : fffffff0
[    7.400000] PrId  : 00019650 (MIPS 24KEc)
[    7.400000] Modules linked in: leds_gpio ohci_hcd ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common
[    7.400000] Process kworker/0:0 (pid: 4, threadinfo=8383e000, task=83828c90, tls=00000000)
[    7.400000] Stack : 00000001 802d0000 83828000 802cfd70 83828c90 8000c0ac 00000000 00000000
          8383fbe0 8383fbe0 83828c90 00000001 83828c88 83828000 83828d6c 00000001
          83828c88 00000000 00000020 800b0f88 80344528 00000002 802d3c98 80340000
          8383fc20 8383fc20 83828db4 800649c0 8383fc20 8383fc4c 8383fd50 80291688
          0000000b 00000028 8380abc0 00000001 00000000 00000000 00800000 800a9b50
          ...
[    7.400000] Call Trace:
[    7.400000] [<801367d4>] kthread_data+0x4/0xc
[    7.400000] [<8024ec80>] wq_worker_sleeping+0x14/0xf4
[    7.400000] [<8000c0ac>] __schedule+0x104/0x558
[    7.400000] [<800b0f88>] do_exit+0x818/0x830
[    7.400000] [<800a9b50>] direct_splice_actor+0x0/0x30
[    7.400000]
[    7.400000]
Code: 03e00008  27bd0048  8c82012c <03e00008> 8c42fff0  0802369a  24840018  10800002  00000000
[    7.780000] ---[ end trace e55cdc53f47faf44 ]---
[    7.790000] Fixing recursive fault but reboot is needed!
[    7.800000] CPU 0 Unable to handle kernel paging request at virtual address fffffff0, epc == 801367d4, ra == 8024ec80
[    7.800000] Oops[#3]:
[    7.800000] CPU: 0 PID: 4 Comm: kworker/0:0 Tainted: G      D      3.10.49 #4
[    7.800000] task: 83828c90 ti: 8383e000 task.ti: 8383e000
[    7.800000] $ 0   : 00000000 00000015 00000000 00000001
[    7.800000] $ 4   : 83828c90 00000000 802cfd70 00000001
[    7.800000] $ 8   : 13d2536e 00000000 00000000 746f6f62
[    7.800000] $12   : 00000000 03bf0000 00000000 746c7561
[    7.800000] $16   : 00000000 0000000b 802d0000 00000028
[    7.800000] $20   : 802cfd70 83828de8 00000000 802cfd70
[    7.800000] $24   : 00000003 8009dc3c                  
[    7.800000] $28   : 8383e000 8383f980 00800000 8024ec80
[    7.800000] Hi    : 00000000
[    7.800000] Lo    : ec4e4000
[    7.800000] epc   : 801367d4 kthread_data+0x4/0xc
[    7.800000]     Tainted: G      D     
[    7.800000] ra    : 8024ec80 wq_worker_sleeping+0x14/0xf4
[    7.800000] Status: 1100a402 KERNEL EXL
[    7.800000] Cause : 80800008
[    7.800000] BadVA : fffffff0
[    7.800000] PrId  : 00019650 (MIPS 24KEc)
[    7.800000] Modules linked in: leds_gpio ohci_hcd ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common
[    7.800000] Process kworker/0:0 (pid: 4, threadinfo=8383e000, task=83828c90, tls=00000000)
[    7.800000] Stack : 0000000b 802d0000 00000028 802cfd70 83828c90 8000c0ac 00000000 00000000
          00800000 8023aa20 83828c90 0000000b 0000000b 00000028 802cfd70 83828de8
          00000000 00000000 00800000 800b0860 80344528 00000038 80285ebb 00000000
          80340000 80133318 00000000 800649c0 802927f0 8383fa0c 8383fb10 80291688
          0000000b 00000028 802cfd70 83828de8 00000000 00000000 00800000 800a9b50
          ...
[    7.800000] Call Trace:
[    7.800000] [<801367d4>] kthread_data+0x4/0xc
[    7.800000] [<8024ec80>] wq_worker_sleeping+0x14/0xf4
[    7.800000] [<8000c0ac>] __schedule+0x104/0x558
[    7.800000] [<800b0860>] do_exit+0xf0/0x830
[    7.800000] [<800a9b50>] direct_splice_actor+0x0/0x30
[    7.800000]
[    7.800000]
Code: 03e00008  27bd0048  8c82012c <03e00008> 8c42fff0  0802369a  24840018  10800002  00000000
[    8.180000] ---[ end trace e55cdc53f47faf45 ]---
[    8.200000] Fixing recursive fault but reboot is needed!
[    8.210000] CPU 0 Unable to handle kernel paging request at virtual address fffffff0, epc == 801367d4, ra == 8024ec80
[    8.210000] Oops[#4]:
[    8.210000] CPU: 0 PID: 4 Comm: kworker/0:0 Tainted: G      D      3.10.49 #4
[    8.210000] task: 83828c90 ti: 8383e000 task.ti: 8383e000
[    8.210000] $ 0   : 00000000 00000015 00000000 00000001
[    8.210000] $ 4   : 83828c90 00000000 802cfd70 00000001
[    8.210000] $ 8   : 13d2536e 00000000 00000000 746f6f62
[    8.210000] $12   : 00000000 03bf0000 00000000 746c7561
[    8.210000] $16   : 00000000 0000000b 802d0000 00000028
[    8.210000] $20   : 802cfd70 83828de8 00000000 802cfd70
[    8.210000] $24   : 00000003 8009dc3c                  
[    8.210000] $28   : 8383e000 8383f740 00800000 8024ec80
[    8.210000] Hi    : 00000000
[    8.210000] Lo    : ec4e4000
[    8.210000] epc   : 801367d4 kthread_data+0x4/0xc
[    8.210000]     Tainted: G      D     
[    8.210000] ra    : 8024ec80 wq_worker_sleeping+0x14/0xf4
[    8.210000] Status: 1100a402 KERNEL EXL
[    8.210000] Cause : 80800008
[    8.210000] BadVA : fffffff0
[    8.210000] PrId  : 00019650 (MIPS 24KEc)
[    8.210000] Modules linked in: leds_gpio ohci_hcd ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common
[    8.210000] Process kworker/0:0 (pid: 4, threadinfo=8383e000, task=83828c90, tls=00000000)
[    8.210000] Stack : 0000000b 802d0000 00000028 802cfd70 83828c90 8000c0ac 00000000 00000000
          00800000 8023aa20 83828c90 0000000b 0000000b 00000028 802cfd70 83828de8
          00000000 00000000 00800000 800b0860 80344528 00000038 80285ebc 00000000
          80340000 80133318 00000000 800649c0 802927f0 8383f7cc 8383f8d0 80291688
          0000000b 00000028 802cfd70 83828de8 00000000 00000000 00800000 800a9b50
          ...
[    8.210000] Call Trace:
[    8.210000] [<801367d4>] kthread_data+0x4/0xc
[    8.210000] [<8024ec80>] wq_worker_sleeping+0x14/0xf4
[    8.210000] [<8000c0ac>] __schedule+0x104/0x558
[    8.210000] [<800b0860>] do_exit+0xf0/0x830
[    8.210000] [<800a9b50>] direct_splice_actor+0x0/0x30
[    8.210000]
[    8.210000]
Code: 03e00008  27bd0048  8c82012c <03e00008> 8c42fff0  0802369a  24840018  10800002  00000000
[    8.590000] ---[ end trace e55cdc53f47faf46 ]---
[    8.600000] Fixing recursive fault but reboot is needed!
[    8.610000] CPU 0 Unable to handle kernel paging request at virtual address fffffff0, epc == 801367d4, ra == 8024ec80
[    8.610000] Oops[#5]:
[    8.610000] CPU: 0 PID: 4 Comm: kworker/0:0 Tainted: G      D      3.10.49 #4
[    8.610000] task: 83828c90 ti: 8383e000 task.ti: 8383e000
[    8.610000] $ 0   : 00000000 00000015 00000000 00000001
[    8.610000] $ 4   : 83828c90 00000000 802cfd70 00000001
[    8.610000] $ 8   : 13d2536e 00000000 00000000 746f6f62
[    8.610000] $12   : 00000000 03bf0000 00000000 746c7561
[    8.610000] $16   : 00000000 0000000b 802d0000 00000028
[    8.610000] $20   : 802cfd70 83828de8 00000000 802cfd70
[    8.610000] $24   : 00000003 8009dc3c                  
[    8.610000] $28   : 8383e000 8383f500 00800000 8024ec80
[    8.610000] Hi    : 00000000
[    8.610000] Lo    : ec4e4000
[    8.610000] epc   : 801367d4 kthread_data+0x4/0xc
[    8.610000]     Tainted: G      D     
[    8.610000] ra    : 8024ec80 wq_worker_sleeping+0x14/0xf4
[    8.610000] Status: 1100a402 KERNEL EXL
[    8.610000] Cause : 80800008
[    8.610000] BadVA : fffffff0
[    8.610000] PrId  : 00019650 (MIPS 24KEc)
[    8.610000] Modules linked in: leds_gpio ohci_hcd ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common
[    8.610000] Process kworker/0:0 (pid: 4, threadinfo=8383e000, task=83828c90, tls=00000000)
[    8.610000] Stack : 0000000b 802d0000 00000028 802cfd70 83828c90 8000c0ac 00000000 00000000
          00800000 8023aa20 83828c90 0000000b 0000000b 00000028 802cfd70 83828de8
          00000000 00000000 00800000 800b0860 80344528 00000038 80285ebc 00000000
          80340000 80133318 00000000 800649c0 802927f0 8383f58c 8383f690 80291688
          0000000b 00000028 802cfd70 83828de8 00000000 00000000 00800000 800a9b50
          ...
[    8.610000] Call Trace:
[    8.610000] [<801367d4>] kthread_data+0x4/0xc
[    8.610000] [<8024ec80>] wq_worker_sleeping+0x14/0xf4
[    8.610000] [<8000c0ac>] __schedule+0x104/0x558
[    8.610000] [<800b0860>] do_exit+0xf0/0x830
[    8.610000] [<800a9b50>] direct_splice_actor+0x0/0x30
[    8.610000]
[    8.610000]
Code: 03e00008  27bd0048  8c82012c <03e00008> 8c42fff0  0802369a  24840018  10800002  00000000
[    8.990000] ---[ end trace e55cdc53f47faf47 ]---
[    9.010000] Fixing recursive fault but reboot is needed!
[    9.020000] CPU 0 Unable to handle kernel paging request at virtual address fffffff0, epc == 801367d4, ra == 8024ec80
[    9.020000] Oops[#6]:
[    9.020000] CPU: 0 PID: 4 Comm: kworker/0:0 Tainted: G      D      3.10.49 #4
[    9.020000] task: 83828c90 ti: 8383e000 task.ti: 8383e000
[    9.020000] $ 0   : 00000000 00000015 00000000 00000001
[    9.020000] $ 4   : 83828c90 00000000 802cfd70 00000001
[    9.020000] $ 8   : 13d2536e 00000000 00000000 746f6f62
[    9.020000] $12   : 00000000 03bf0000 00000000 746c7561
[    9.020000] $16   : 00000000 0000000b 802d0000 00000028
[    9.020000] $20   : 802cfd70 83828de8 00000000 802cfd70
[    9.020000] $24   : 00000003 8009dc3c                  
[    9.020000] $28   : 8383e000 8383f2c0 00800000 8024ec80
[    9.020000] Hi    : 00000000
[    9.020000] Lo    : ec4e4000
[    9.020000] epc   : 801367d4 kthread_data+0x4/0xc
[    9.020000]     Tainted: G      D     
[    9.020000] ra    : 8024ec80 wq_worker_sleeping+0x14/0xf4
[    9.020000] Status: 1100a402 KERNEL EXL
[    9.020000] Cause : 80800008
[    9.020000] BadVA : fffffff0
[    9.020000] PrId  : 00019650 (MIPS 24KEc)
[    9.020000] Modules linked in: leds_gpio ohci_hcd ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common
[    9.020000] Process kworker/0:0 (pid: 4, threadinfo=8383e000, task=83828c90, tls=00000000)
[    9.020000] Stack : 0000000b 802d0000 00000028 802cfd70 83828c90 8000c0ac 00000000 00000000
          00800000 8023aa20 83828c90 0000000b 0000000b 00000028 802cfd70 83828de8
          00000000 00000000 00800000 800b0860 80344528 00000038 80285ebc 00000000
          80340000 80133318 00000000 800649c0 802927f0 8383f34c 8383f450 80291688
          0000000b 00000028 802cfd70 83828de8 00000000 00000000 00800000 800a9b50
          ...
[    9.020000] Call Trace:
[    9.020000] [<801367d4>] kthread_data+0x4/0xc
[    9.020000] [<8024ec80>] wq_worker_sleeping+0x14/0xf4
[    9.020000] [<8000c0ac>] __schedule+0x104/0x558
[    9.020000] [<800b0860>] do_exit+0xf0/0x830
[    9.020000] [<800a9b50>] direct_splice_actor+0x0/0x30
[    9.020000]
[    9.020000]
Code: 03e00008  27bd0048  8c82012c <03e00008> 8c42fff0  0802369a  24840018  10800002  00000000
[    9.400000] ---[ end trace e55cdc53f47faf48 ]---
[    9.410000] Fixing recursive fault but reboot is needed!
[    9.420000] CPU 0 Unable to handle kernel paging request at virtual address fffffff0, epc == 801367d4, ra == 8024ec80
[    9.420000] Oops[#7]:
[    9.420000] CPU: 0 PID: 4 Comm: kworker/0:0 Tainted: G      D      3.10.49 #4
[    9.420000] task: 83828c90 ti: 8383e000 task.ti: 8383e000
[    9.420000] $ 0   : 00000000 00000015 00000000 00000001
[    9.420000] $ 4   : 83828c90 00000000 802cfd70 00000001
[    9.420000] $ 8   : 13d2536e 00000000 00000000 746f6f62
[    9.420000] $12   : 00000000 03bf0000 00000000 746c7561
[    9.420000] $16   : 00000000 0000000b 802d0000 00000028
[    9.420000] $20   : 802cfd70 83828de8 00000000 802cfd70
[    9.420000] $24   : 00000003 8009dc3c                  
[    9.420000] $28   : 8383e000 8383f080 00800000 8024ec80
[    9.420000] Hi    : 00000000
[    9.420000] Lo    : ec4e4000
[    9.420000] epc   : 801367d4 kthread_data+0x4/0xc
[    9.420000]     Tainted: G      D     
[    9.420000] ra    : 8024ec80 wq_worker_sleeping+0x14/0xf4
[    9.420000] Status: 1100a402 KERNEL EXL
[    9.420000] Cause : 80800008
[    9.420000] BadVA : fffffff0
[    9.420000] PrId  : 00019650 (MIPS 24KEc)
[    9.420000] Modules linked in: leds_gpio ohci_hcd ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common
[    9.420000] Process kworker/0:0 (pid: 4, threadinfo=8383e000, task=83828c90, tls=00000000)
[    9.420000] Stack : 0000000b 802d0000 00000028 802cfd70 83828c90 8000c0ac 00000000 00000000
          00800000 8023aa20 83828c90 0000000b 0000000b 00000028 802cfd70 83828de8
          00000000 00000000 00800000 800b0860 80344528 00000038 80285ebd 00000000
          80340000 80133318 00000000 800649c0 802927f0 8383f10c 8383f210 80291688
          0000000b 00000028 802cfd70 83828de8 00000000 00000000 00800000 800a9b50
          ...
[    9.420000] Call Trace:
[    9.420000] [<801367d4>] kthread_data+0x4/0xc
[    9.420000] [<8024ec80>] wq_worker_sleeping+0x14/0xf4
[    9.420000] [<8000c0ac>] __schedule+0x104/0x558
[    9.420000] [<800b0860>] do_exit+0xf0/0x830
[    9.420000] [<800a9b50>] direct_splice_actor+0x0/0x30
[    9.420000]
[    9.420000]
Code: 03e00008  27bd0048  8c82012c <03e00008> 8c42fff0  0802369a  24840018  10800002  00000000
[    9.810000] ---[ end trace e55cdc53f47faf49 ]---
[    9.820000] Fixing recursive fault but reboot is needed!
[    9.830000] CPU 0 Unable to handle kernel paging request at virtual address fffffff0, epc == 801367d4, ra == 8024ec80
[    9.830000] Oops[#8]:
[    9.830000] CPU: 0 PID: 4 Comm: kworker/0:0 Tainted: G      D      3.10.49 #4
[    9.830000] task: 83828c90 ti: 8383e000 task.ti: 8383e000
[    9.830000] $ 0   : 00000000 00000015 00000000 00000001
[    9.830000] $ 4   : 83828c90 00000000 802cfd70 00000001
[    9.830000] $ 8   : 13d2536e 00000000 00000000 746f6f62
[    9.830000] $12   : 00000000 03bf0000 00000000 746c7561
[    9.830000] $16   : 00000000 0000000b 802d0000 00000028
[    9.830000] $20   : 802cfd70 83828de8 00000000 802cfd70
[    9.830000] $24   : 00000003 8009dc3c                  
[    9.830000] $28   : 8383e000 8383ee40 00800000 8024ec80
[    9.830000] Hi    : 00000000
[    9.830000] Lo    : ec4e4000
[    9.830000] epc   : 801367d4 kthread_data+0x4/0xc
[    9.830000]     Tainted: G      D     
[    9.830000] ra    : 8024ec80 wq_worker_sleeping+0x14/0xf4
[    9.830000] Status: 1100a402 KERNEL EXL
[    9.830000] Cause : 80800008
[    9.830000] BadVA : fffffff0
[    9.830000] PrId  : 00019650 (MIPS 24KEc)
[    9.830000] Modules linked in: leds_gpio ohci_hcd ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common
[    9.830000] Process kworker/0:0 (pid: 4, threadinfo=8383e000, task=83828c90, tls=00000000)
[    9.830000] Stack : 0000000b 802d0000 00000028 802cfd70 83828c90 8000c0ac 00000000 00000000
          00800000 8023aa20 83828c90 0000000b 0000000b 00000028 802cfd70 83828de8
          00000000 00000000 00800000 800b0860 80344528 00000038 80285ebd 00000000
          80340000 80133318 00000000 800649c0 802927f0 8383eecc 8383efd0 80291688
          0000000b 00000028 802cfd70 83828de8 00000000 00000000 00800000 800a9b50
          ...
[    9.830000] Call Trace:
[    9.830000] [<801367d4>] kthread_data+0x4/0xc
[    9.830000] [<8024ec80>] wq_worker_sleeping+0x14/0xf4
[    9.830000] [<8000c0ac>] __schedule+0x104/0x558
[    9.830000] [<800b0860>] do_exit+0xf0/0x830
[    9.830000] [<800a9b50>] direct_splice_actor+0x0/0x30
[    9.830000]
[    9.830000]
Code: 03e00008  27bd0048  8c82012c <03e00008> 8c42fff0  0802369a  24840018  10800002  00000000
[   10.210000] ---[ end trace e55cdc53f47faf4a ]---
[   10.230000] Fixing recursive fault but reboot is needed!
[   10.240000] CPU 0 Unable to handle kernel paging request at virtual address fffffff0, epc == 801367d4, ra == 8024ec80
[   10.240000] Oops[#9]:
[   10.240000] CPU: 0 PID: 4 Comm: kworker/0:0 Tainted: G      D      3.10.49 #4
[   10.240000] task: 83828c90 ti: 8383e000 task.ti: 8383e000
[   10.240000] $ 0   : 00000000 00000015 00000000 00000001
[   10.240000] $ 4   : 83828c90 00000000 802cfd70 00000001
[   10.240000] $ 8   : 13d2536e 00000000 00000000 746f6f62
[   10.240000] $12   : 00000000 03bf0000 00000000 746c7561
[   10.240000] $16   : 00000000 0000000b 802d0000 00000028
[   10.240000] $20   : 802cfd70 83828de8 00000000 802cfd70
[   10.240000] $24   : 00000003 8009dc3c                  
[   10.240000] $28   : 8383e000 8383ec00 00800000 8024ec80
[   10.240000] Hi    : 00000000
[   10.240000] Lo    : ec4e4000
[   10.240000] epc   : 801367d4 kthread_data+0x4/0xc
[   10.240000]     Tainted: G      D     
[   10.240000] ra    : 8024ec80 wq_worker_sleeping+0x14/0xf4
[   10.240000] Status: 1100a402 KERNEL EXL
[   10.240000] Cause : 80800008
[   10.240000] BadVA : fffffff0
[   10.240000] PrId  : 00019650 (MIPS 24KEc)
[   10.240000] Modules linked in: leds_gpio ohci_hcd ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common
[   10.240000] Process kworker/0:0 (pid: 4, threadinfo=8383e000, task=83828c90, tls=00000000)
[   10.240000] Stack : 0000000b 802d0000 00000028 802cfd70 83828c90 8000c0ac 00000000 00000000
          00800000 8023aa20 83828c90 0000000b 0000000b 00000028 802cfd70 83828de8
          00000000 00000000 00800000 800b0860 80344528 00000038 00000000 0000000a
          80340000 80133318 00000000 800649c0 802927f0 8383ec8c 8383ed90 80291688
          0000000b 00000028 802cfd70 83828de8 00000000 00000000 00800000 800a9b50
          ...
[   10.240000] Call Trace:
[   10.240000] [<801367d4>] kthread_data+0x4/0xc
[   10.240000] [<8024ec80>] wq_worker_sleeping+0x14/0xf4
[   10.240000] [<8000c0ac>] __schedule+0x104/0x558
[   10.240000] [<800b0860>] do_exit+0xf0/0x830
[   10.240000] [<800a9b50>] direct_splice_actor+0x0/0x30
[   10.240000]
[   10.240000]
Code: 03e00008  27bd0048  8c82012c <03e00008> 8c42fff0  0802369a  24840018  10800002  00000000
[   10.620000] ---[ end trace e55cdc53f47faf4b ]---
[   10.630000] Fixing recursive fault but reboot is needed!
[   10.640000] CPU 0 Unable to handle kernel paging request at virtual address fffffff0, epc == 801367d4, ra == 8024ec80
[   10.640000] Oops[#10]:
[   10.640000] CPU: 0 PID: 4 Comm: kworker/0:0 Tainted: G      D      3.10.49 #4
[   10.640000] task: 83828c90 ti: 8383e000 task.ti: 8383e000
[   10.640000] $ 0   : 00000000 00000015 00000000 00000001
[   10.640000] $ 4   : 83828c90 00000000 802cfd70 00000001
[   10.640000] $ 8   : 13d2536e 00000000 00000000 746f6f62
[   10.640000] $12   : 00000000 03bf0000 00000000 746c7561
[   10.640000] $16   : 00000000 0000000b 802d0000 00000028
[   10.640000] $20   : 802cfd70 83828de8 00000000 802cfd70
[   10.640000] $24   : 00000003 8009dc3c                  
[   10.640000] $28   : 8383e000 8383e9c0 00800000 8024ec80
[   10.640000] Hi    : 00000000
[   10.640000] Lo    : ec4e4000
[   10.640000] epc   : 801367d4 kthread_data+0x4/0xc
[   10.640000]     Tainted: G      D     
[   10.640000] ra    : 8024ec80 wq_worker_sleeping+0x14/0xf4
[   10.640000] Status: 1100a402 KERNEL EXL
[   10.640000] Cause : 80800008
[   10.640000] BadVA : fffffff0
[   10.640000] PrId  : 00019650 (MIPS 24KEc)
[   10.640000] Modules linked in: leds_gpio ohci_hcd ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common
[   10.640000] Process kworker/0:0 (pid: 4, threadinfo=8383e000, task=83828c90, tls=00000000)
[   10.640000] Stack : 0000000b 802d0000 00000028 802cfd70 83828c90 8000c0ac 00000000 00000000
          00800000 8023aa20 83828c90 0000000b 0000000b 00000028 802cfd70 83828de8
          00000000 00000000 00800000 800b0860 80344528 00000038 00000000 0000000a
          80340000 80133318 00000000 800649c0 802927f0 8383ea4c 8383eb50 80291688
          0000000b 00000028 802cfd70 83828de8 00000000 00000000 00800000 800a9b50
          ...
[   10.640000] Call Trace:
[   10.640000] [<801367d4>] kthread_data+0x4/0xc
[   10.640000] [<8024ec80>] wq_worker_sleeping+0x14/0xf4
[   10.640000] [<8000c0ac>] __schedule+0x104/0x558
[   10.640000] [<800b0860>] do_exit+0xf0/0x830
[   10.640000] [<800a9b50>] direct_splice_actor+0x0/0x30
[   10.640000]
[   10.640000]
Code: 03e00008  27bd0048  8c82012c <03e00008> 8c42fff0  0802369a  24840018  10800002  00000000
[   11.030000] ---[ end trace e55cdc53f47faf4c ]---
[   11.040000] Fixing recursive fault but reboot is needed!
[   11.050000] CPU 0 Unable to handle kernel paging request at virtual address fffffff0, epc == 801367d4, ra == 8024ec80
[   11.050000] Oops[#11]:
[   11.050000] CPU: 0 PID: 4 Comm: kworker/0:0 Tainted: G      D      3.10.49 #4
[   11.050000] task: 83828c90 ti: 8383e000 task.ti: 8383e000
[   11.050000] $ 0   : 00000000 00000015 00000000 00000001
[   11.050000] $ 4   : 83828c90 00000000 802cfd70 00000001
[   11.050000] $ 8   : 13d2536e 00000000 00000000 746f6f62
[   11.050000] $12   : 00000000 03bf0000 00000000 746c7561
[   11.050000] $16   : 00000000 0000000b 802d0000 00000028
[   11.050000] $20   : 802cfd70 83828de8 00000000 802cfd70
[   11.050000] $24   : 00000003 8009dc3c                  
[   11.050000] $28   : 8383e000 8383e780 00800000 8024ec80
[   11.050000] Hi    : 00000000
[   11.050000] Lo    : ec4e4000
[   11.050000] epc   : 801367d4 kthread_data+0x4/0xc
[   11.050000]     Tainted: G      D     
[   11.050000] ra    : 8024ec80 wq_worker_sleeping+0x14/0xf4
[   11.050000] Status: 1100a402 KERNEL EXL
[   11.050000] Cause : 80800008
[   11.050000] BadVA : fffffff0
[   11.050000] PrId  : 00019650 (MIPS 24KEc)
[   11.050000] Modules linked in: leds_gpio ohci_hcd ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common
[   11.050000] Process kworker/0:0 (pid: 4, threadinfo=8383e000, task=83828c90, tls=00000000)
[   11.050000] Stack : 0000000b 802d0000 00000028 802cfd70 83828c90 8000c0ac 00000000 00000000
          00800000 8023aa20 83828c90 0000000b 0000000b 00000028 802cfd70 83828de8
          00000000 00000000 00800000 800b0860 80344528 00000038 00000000 0000000a
          80340000 80133318 00000000 800649c0 802927f0 8383e80c 8383e910 80291688
          0000000b 00000028 802cfd70 83828de8 00000000 00000000 00800000 800a9b50
          ...
[   11.050000] Call Trace:
[   11.050000] [<801367d4>] kthread_data+0x4/0xc
[   11.050000] [<8024ec80>] wq_worker_sleeping+0x14/0xf4
[   11.050000] [<8000c0ac>] __schedule+0x104/0x558
[   11.050000] [<800b0860>] do_exit+0xf0/0x830
[   11.050000] [<800a9b50>] direct_splice_actor+0x0/0x30
[   11.050000]
[   11.050000]
Code: 03e00008  27bd0048  8c82012c <03e00008> 8c42fff0  0802369a  24840018  10800002  00000000
[   11.440000] ---[ end trace e55cdc53f47faf4d ]---
[   11.450000] Fixing recursive fault but reboot is needed!
[   11.460000] CPU 0 Unable to handle kernel paging request at virtual address fffffff0, epc == 801367d4, ra == 8024ec80
[   11.460000] Oops[#12]:
[   11.460000] CPU: 0 PID: 4 Comm: kworker/0:0 Tainted: G      D      3.10.49 #4
[   11.460000] task: 83828c90 ti: 8383e000 task.ti: 8383e000
[   11.460000] $ 0   : 00000000 00000015 00000000 00000001
[   11.460000] $ 4   : 83828c90 00000000 802cfd70 00000001
[   11.460000] $ 8   : 13d2536e 00000000 00000000 746f6f62
[   11.460000] $12   : 00000000 03bf0000 00000000 746c7561
[   11.460000] $16   : 00000000 0000000b 802d0000 00000028
[   11.460000] $20   : 802cfd70 83828de8 00000000 802cfd70
[   11.460000] $24   : 00000003 8009dc3c                  
[   11.460000] $28   : 8383e000 8383e540 00800000 8024ec80
[   11.460000] Hi    : 00000000
[   11.460000] Lo    : ec4e4000
[   11.460000] epc   : 801367d4 kthread_data+0x4/0xc
[   11.460000]     Tainted: G      D     
[   11.460000] ra    : 8024ec80 wq_worker_sleeping+0x14/0xf4
[   11.460000] Status: 1100a402 KERNEL EXL
[   11.460000] Cause : 80800008
[   11.460000] BadVA : fffffff0
[   11.460000] PrId  : 00019650 (MIPS 24KEc)
[   11.460000] Modules linked in: leds_gpio ohci_hcd ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common
[   11.460000] Process kworker/0:0 (pid: 4, threadinfo=8383e000, task=83828c90, tls=00000000)
[   11.460000] Stack : 0000000b 802d0000 00000028 802cfd70 83828c90 8000c0ac 00000000 00000000
          00800000 8023aa20 83828c90 0000000b 0000000b 00000028 802cfd70 83828de8
          00000000 00000000 00800000 800b0860 80344528 00000038 00000000 0000000a
          80340000 80133318 00000000 800649c0 802927f0 8383e5cc 8383e6d0 80291688
          0000000b 00000028 802cfd70 83828de8 00000000 00000000 00800000 800a9b50
          ...
[   11.460000] Call Trace:
[   11.460000] [<801367d4>] kthread_data+0x4/0xc
[   11.460000] [<8024ec80>] wq_worker_sleeping+0x14/0xf4
[   11.460000] [<8000c0ac>] __schedule+0x104/0x558
[   11.460000] [<800b0860>] do_exit+0xf0/0x830
[   11.460000] [<800a9b50>] direct_splice_actor+0x0/0x30
[   11.460000]
[   11.460000]
Code: 03e00008  27bd0048  8c82012c <03e00008> 8c42fff0  0802369a  24840018  10800002  00000000
[   11.840000] ---[ end trace e55cdc53f47faf4e ]---
[   11.860000] Kernel panic - not syncing: Fatal exception in interrupt