hi3531内核启动到一般卡主了

用的是官方的uboot和内核，不知道大家有什么建议？谁有完整的启动日志能贴出来看眼吗？我好分析分析

启动日志如下：

[quote]NAND read: device 0 offset 0x100000, size 0x500000
5242880 bytes read: OK
## Booting kernel from Legacy Image at 82000000 ...
   Image Name:   Linux-3.0.8
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3496508 Bytes = 3.3 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 3.0.8 (pub@BVT-SDK-174) (gcc version 4.4.1 (Hisilicon_v100(gcc4.4-290+uclibc_0.9.32.1+eabi+linuxpthread)) ) #1 SMP Fri Aug 24 16:58:34 CST 2012
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: godnet
Memory policy: ECC disabled, Data cache writealloc
PERCPU: Embedded 7 pages/cpu @c0741000 s5152 r8192 d15328 u32768
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: mem=64M console=ttyAMA0,115200 root=/dev/mtdblock2 rootfstype=jffs2 mtdparts=hinand:1M(boot),15M(kernel),32M(rootfs),16M(test) mac=00:1B:43:85:24:5A ipaddr=10.0.0.254 netmask=255.0.0.0
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 57992k/57992k available, 7544k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
    vmalloc : 0xc4800000 - 0xfe000000   ( 920 MB)
    lowmem  : 0xc0000000 - 0xc4000000   (  64 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .init : 0xc0008000 - 0xc0036000   ( 184 kB)
      .text : 0xc0036000 - 0xc0639000   (6156 kB)
      .data : 0xc063a000 - 0xc0660f00   ( 156 kB)
       .bss : 0xc0660f24 - 0xc06bd654   ( 370 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:128 nr_irqs:128 128
sched_clock: 32 bits at 155MHz, resolution 6ns, wraps every 27709ms
sched_clock: wrong multiply/shift: 432960413>>26 vs calculated 3463683303>>29
sched_clock: fix multiply/shift to avoid scheduler hiccups
Console: colour dummy device 80x30
Calibrating delay loop... 1849.75 BogoMIPS (lpj=9248768)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
CPU1: Booted secondary processor
Brought up 2 CPUs
SMP: Total of 2 processors activated (3706.06 BogoMIPS).
NET: Registered protocol family 16
Serial: AMBA PL011 UART driver
uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 40) is a PL011 rev2
console [ttyAMA0] enabled
uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 41) is a PL011 rev2
bio: create slab at 0
controller0, config base:0x20800000, mem size:0x800000
controller1, config base:0x20810000, mem size:0x800000-->卡在此处[/quote]